Filter By:
- Show More Brands
- Show Fewer Brands
- Show More Sizes
- Show Fewer Sizes
Tools
$2.00
Replacement threaded cap for Abbey Hanger Alligment Gauge Tool.
$25.00
The soft face on the Titanium Hammer is destined to be gouged, get worn down, or even melt (if you leave it near heat).
Replacement soft face for Abbey Titanium Hammer.
$30.00
Replacement pins, these are original equipment chain pins for our chain tool, they also work as an alternate to the Campagnolo UT-CN300 11spd chain tool, Shimano CN-34 and CN-32
Sold in pairs.
$30.00
Replacement feeler gauge for the Abbey Hanger Alligment Gauge Tool.
$30.00
For use with 1/4" Micro Bearing Press Shaft
$30.50
The soft face on the Shop Hammer is destined to be gouged, get worn down, or even melt (if you leave it near heat).
Replacement soft face for Abbey Shop Hammer.
$45.00
Replacement 6/8mm Hex bit for both the Abbey BBQ Wood Handled Pedal Wrench and the Team Issue Pedal Wrench.
$45.50
The magnetic saddle height bullet ensures you get an accurate center at the bottom bracket by locating in the crank arm fixing bolt or the crank arm preload cap of Shimano caps. This allows you to focus on the smart end of the tape measure at the saddle plate.
$45.50
The magnetic saddle height bullet ensures you get an accurate center at the bottom bracket by locating in the crank arm fixing bolt or the crank arm preload cap of Shimano caps. This allows you to focus on the smart end of the tape measure at the saddle plate.
$59.50
1/8" mid plate, needed to use the Decade chain tool with wide 1/8" track and single speed chains.
$59.50
For use with the Decade Chain Tool this AXS Mid Plate is required for the SRAM AXS Road and the new MTB Transmission Flat Top chains.
This part is not needed for other 12spd chains from various manufacturers. The mid plate is visually differentiated from the other Decade mid plates by three dots on the face of the plate.
$63.50
The Stu Stick is a 44-gram rotor truing tool. Whether you want to slip it into your hydration pack for that enduro mountain bike ride or travel the world working with one of the staples of cross racing, it's up to the task. You can even use it to crack open a beer after you're done with the day's fun.
- Weight: 44g
- Made of aluminum
$71.00
These gems are machined to precisely fit the preload adjuster cap on all modern 24mm spindle Shimano cranks. The finger spline offers good leverage to install, remove, or adjust the preload cap. We also added a 5mm hex in the center should you need a little extra leverage that a hex key provides. These are also compatible with our fit kits and with the addition of a saddle height bullet can be used to more accurately measure saddle height.
$75.50
This is a 13mm socket made specifically for the bleeders on modern Fox forks.
These bleeders are built just like a top cap, with minimal height of the hex drive. So it's a perfect application for our original chamferless sockets. Use these to install the fenders that mount behind the bleeders or when servicing your fork.
Socket uses a 3/8" square drive.
Compatibility:
Fox fork models 36,38 and 40 equipped with bleeders.
$78.00
This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm.
The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet.
The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.
*** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.
$78.00
This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm.
The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet.
The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.
*** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.
$78.00
This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm.
The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet.
The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.
*** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.
$78.00
This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm.
The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet.
The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.
*** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.
$78.00
This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm.
The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet.
The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.
*** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.
$78.00
This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm.
The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet.
The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.
*** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.
$78.00
This tool makes dust wiper installation an easy task.
The Fork Seal Press is built with modern tight fitting fork seals in mind. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.
$85.00
Bearing drift designed for the SRAM DUB crank platform and use with the Abbey Bike Tools Modular bearing press.
SRAM recently launched a new crank platform called DUB to improve bearing durability and compatibility that modern frames have dictated. This 28.99mm spindle and its press fit bottom bracket requires some special drifts to install correctly. We worked with the crew at SRAM to develop tools for this and came up with some simple and important tweaks from a standard bearing drift.
These drifts have a tapered boss that forces the small O ring into its gland. A normal drift with a square boss can easily tear the fragile O ring that helps with bearing durability. So this basic modification makes sure your bottom bracket retains the durability it was designed to have.
- Comes as a set of two drifts
$86.50
This simple tool is designed to remove and install the static bearing in the shock ends of many modern rear shocks.
Machined from durable stainless steel this compact tool allows the user to remove and install the DU bushings without resorting to hammers and punches. The coarse acme thread keeps the constant turning to a minimum.
$89.00 - $115.00
All the awesomeness of the dual-sided tool but in a single Shimano or Campagnolo version. Updated in 2020, the single-sided tool now has the same size handle (1/2 inch) as the dual-sided tool.
- When purchasing the chain whip, buy the 1/2-inch handle chain whip.
$89.50
This dedicated socket is built to engage all 4 of the holes on a SRAM dub crank arm dust cap. These caps don't normally need to be removed but when you do need to work with them, few things work well. These tools feature a common 3/8" square drive like the rest of our socket range and also have a hexagonal exterior so you can mount them in a vise and use the crank arm as the lever if so desired. The sockets are also marked for the left hand thread (clockwise to loosen) this part uses.
Compatible with all SRAM dub cranks, road/mountain/gravel.
$99.40 - $425.70
Suspension service is a specialty within bicycle repair, and it takes specialized tools to perform this work. One of the things that any factory tech will tell you is nice to have are sockets specifically made or altered for the low profile hex on the top of each fork leg. The lead-in or chamfer on a standard socket will greatly decrease the contact between tool and part and can easily scratch or deform those nuts. For years shops have been grinding down their sockets to remove the chamfer. The problem is that you're still often left with a loose-fitting socket that is still prone to chewing up those delicate parts. That's why we started from scratch.
We made our sockets from billet aluminum to exacting tolerances to keep these parts in good shape. Fully CNC-machined with zero lead-in, they make the specialty that is suspension service a little bit easier. They feature a 3/8" square drive for use with your favorite torque wrench as well as finger splines to help run the top caps into the fork legs with those oil soaked hands. We also kept them short (1" or 25mm for all sizes) to reduce the chance of them slipping off of the top cap under torque.
- Made from billet aluminum to exacting tolerances to keep form damaging the suspension
- Finger splines so you can thread it easily by hand
- 3/8" square drive
- Short (1"/25mm for all sizes) to reduce the chance of them coming off of the top cap under torque
- Made in Bend, Oregon
Applications
- 24mm socket - used on SRAM top caps
- 26mm socket - used on Marzocchi and Reverb sealheads
- 27mm socket - used on Fox and X-Fusion top caps
- 30mm socket - used on the RS-1 SRAM sealhead removal tool as well as a handful of other forks.
- 6-size set covers most modern suspension forks on the market: 24, 26, 27, 28, 30 and 32mm
$104.00
The lever setter is a unique tool that works in conjunction with our HAG (or other hanger allignment tool) to set brake and shifter levers at the same height from side to side. The tool temporarily replaces the headset top cap and allows you to thread a hanger alignment tool into the lever setter. Use the HAG indicator to set levers the same from one side of the bar to the other. Once you're satisfied with your lever placement simply remove the tool and replace your headset top cap and go ride.
Compatibility:
Requires a star nut or compression plug with a M6x1 thread.
Works with road and mountain shifters and brake levers.
Compatible with most hanger alignment tools on the market.
Recommendations:
It's advised to use a spacer on top of the stem to help align the lever setter with the steer tube. This will reduce the impact the quality of the cut on the steer tube has on the function of the tool. The supplied threaded stud can be replaced with a longer one if needed.
$105.00
The Shimano Crank Tool (SCT for short) is specifically built to service the chainring lockring on Shimano single ring cranksets for 12 speed drivetrains. It features a large hex that can be used with a 1.5" or 38mm wrench or locked into a vise. The clearance hole is kept to a minimum to keep the tool engaged on the low profile lockring, minimizing the chance of damaging the tool or parts.
Compatibility:
- Chain ring lockrings on Shimano 12spd mountain crank sets.
- XT and Ultegra bottom brackets
$115.50
The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket.
Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag.
The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night.
Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed.
These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.
Page 1 of 2
Next page